Sign In | Join Free | My xpandrally.com
xpandrally.com
Products
Search by Category
Home > Flexible Tube >

Concrete Joint and Seam Filler

Country/Region china
Company Zhejiang Taizheng Construction Material Co., Ltd
Categories Set Retarder Concrete Admixture
Telephone +86-571-87569602
ICP License Issued by the Chinese Ministry
  • Haven't found right suppliers
  • Our buyer assistants can help you find the most suitable, 100% reliable suppliers from China.
  • And this service is free of charge.
  • we have buyer assistants who speak English, French, Spanish......and we are ready to help you anytime!
  • Submit Buying Request
    • Product Details
    • Company Profile

    Concrete Joint and Seam Filler

    Product Details

    PRODUCT DESCRIPTION

    Tasir -Joint Filler is a one component, 100% solids, solvent-free adhesive and void filler for use on multiple substrates. This product can be used to fill voids or gaps of up to 3/4"and is perfect as a sealer/adhesive for use with the Tasir Centrifugal cast industrial pipe repair system.

    ADVANTAGES

    Fills gaps up to 3/4”

    Superior shore hardness

    Remains flexible and suitable for use where shock, vibration, shrinking or swelling are concerns.

    Environmentally friendly—solvent free, isocyanate free and low VOC

    Tack free in < 30 minutes for increased productivity

    Non-sag for ease of placement

    USES

    Fill and repair voids in multiple substrates

    Seal industrial pipe voids prior to application of repair mortar

    Tasir Centrifugal cast industrial pipe repair system

    PACKAGING

    Tasir -Joint Filler is packaged in 20 oz. sausage tubes for use in manual or pneumatic guns.

    SHELF LIFE

    One year from manufacture date in original unopened packaging when stored in dry conditions below 80°F (27°C).

    Note: Due to the wide variety of substrates, preparation methods, application methods and environments, always test a small area of substrate to verify desired results.

    TYPICAL PROPERTIES AT 70°F (21°C)

    Cured Properties at 21 Days

    Tensile Bond (Fiberglass)

    175 psi (1.20 MPa)

    Hardness, Shore A, ASTM D 2240

    60

    Tensile Strength, ASTM D 412

    260 psi (1.8 MPa)

    Elongation, ASTM D 412

    250%

    Peel Strength, ASTM D 1004

    60 lbs/in (1,056 kg/m)

    Uncured Properties

    Cure Rate

    1/4" - 16 hours

    VOC Content

    < 30g/liter

    The data shown above reflects typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result. Test methods are modified where applicable.

    PLACEMENT GUIDELINES

    1. SURFACE PREPARATION: Surfaces must be clean, sound, and free of any growth, dirt, oxidation, rust or other bond inhibiting contaminants. High-pressure water blasting or abrasive blasting of surfaces is recommended. Coat areas as soon as possible after surface preparation to minimize corrosion to newly prepared surfaces.

    2. PLACEMENT: Place cartridge in appropriate sausage gun with applicable tip to achieve desired bead of material. Dispense following application gun's instructions. Tasir -Joint Filler should be applied at a surface temperature of at least 40°F (5°C) or higher.

    3. CLEAN-UP: Mineral Spirits, Denatured Alcohol, or VM&P solvent may be used for clean up of tools and equipment.

    NOTE: PRIOR TO APPLICATION, READ ALL PRODUCT PACKAGING THOROUGHLY. For more detailed placement procedures, refer to Tasir installation guidelines or call Tasir Products'Engineering and Technical Service Center at +86-571-87569602.

    CAUTION:

    Irritant, toxic, strong sensitizer. This product may cause skin irritation. Do not inhale vapors. Provide adequate ventilation. Protect against contact with skin and eyes. Wear rubber gloves, long sleeve shirt, goggles with side shields. In case of contact with eyes, flush repeatedly with water and contact a physician. Areas of skin contact should be promptly washed with soap and water. Wash thoroughly after handling. Do not take internally. Keep product out of reach of children. Keep container closed when not in use. PRIOR TO USE, REFER TO SAFETY DATA SHEET.

    For worldwide availability, additional product information and technical support, contact your local Tasir distributor, local sales representative, or call Tasir roducts'Engineering and Technical Service Center at +86-571-87569602.

    SKU/PRODUCT CODE

    DESCRIPTION

    # UNITS/PALLET

    UNIT SIZE

    JF

    Tasir -Joint Filler

    45

    20 oz. (0.6 kg) Sausage Tubes
    12 tubes / case

    WARRANTY: Tasir PRODUCTS ARE MANUFACTURED TO BE FREE OF MANUFACTURING DEFECTS AND TO MEET FSP'S CURRENT PUBLISHED PH

    Product Tags:

    rubber gloves

      

    product packaging

      
    Quality Concrete Joint and Seam Filler for sale
    Send your message to this supplier
     
    From:
    To: Zhejiang Taizheng Construction Material Co., Ltd
    Subject:
    Message:
    Characters Remaining: (0/3000)
     
    Inquiry Cart 0